Do you offer electrostatic painting in Melbourne Village, FL?

Yes. Pro Touch Painting provides electrostatic painting throughout Melbourne Village and the rest of Brevard County. Call 207-812-1837 for a free written estimate.

What is electrostatic painting?

Electrostatic painting is a spray method that gives the paint particles an electrical charge so they are attracted to grounded metal. The coating wraps around the whole surface — front, back, edges, hinges and railing undersides — and very little of it drifts as overspray. That makes it the standard way to refinish metal on site instead of removing it or replacing it.

What can be electrostatically painted?

Any grounded metal: hollow metal doors and frames, handrails and guardrails, lockers, shelving and racking, storefront and window frames, elevator doors, partitions, filing cabinets, electrical panels, HVAC units, machinery housings and metal fencing. Wood, drywall, plastic and fiberglass cannot hold the charge and are painted conventionally instead.

Can you paint while our building stays open?

Yes — that is the main reason to choose it. Because the charged coating is pulled to the metal rather than into the air, containment and masking are far lighter than conventional spraying, so we work in occupied offices, schools, medical suites, retail spaces and warehouses, section by section, including evenings and weekends.

Melbourne Village, FL · Brevard County

Electrostatic Painting in Melbourne Village, FL

Pro Touch Painting offers on-site electrostatic painting throughout Brevard County, FL — hollow metal doors and frames, handrails, lockers, shelving, storefronts, machinery, panels and warehouse racking are refinished in place with an electrostatically charged coating that wraps around metal, so occupied offices, schools, medical suites and warehouses stay open while the work happens.

Get a Free Estimate 207-812-1837

5.0 from 39 reviews Licensed & insured Local Melbourne Village crews

Electrostatic Painting project by Pro Touch Painting in Melbourne Village, Brevard County FL

Why Melbourne Village homes need electrostatic painting done right

Melbourne Village is a small wooded town off US-192 with mid-century frame and block homes set under heavy oak canopy. That shade keeps homes cool but also keeps exterior walls damp, so mildew, algae streaking and chalky old paint are the norm before we start. Wood fascia, soffits and siding get scraped, repaired and primed; block and stucco walls get crack repair and a breathable acrylic system. Interiors here are usually older plaster or textured drywall that benefits from patching and a proper primer coat before color.

Electrostatic painting solves a problem conventional spraying cannot: refinishing metal inside a building that is still in use. The gun gives the atomized coating a negative charge, the grounded metal pulls it in, and the paint wraps around edges, hinges, tube railings and louvers instead of drifting into the room. The result is a hard, even, factory-like film on metal that would otherwise have to be removed, sent out, or replaced — with dramatically less masking, overspray and downtime than a standard spray job.

Heavy oak canopy and shade

Damp, shaded elevations are pressure washed and mildew-treated so new paint bonds instead of peeling off algae growth.

Mid-century frame homes

Wood siding, fascia and soffits get rot repair, caulking and full priming before finish coats — the prep is most of the job.

How we approach electrostatic painting in Melbourne Village, Florida

Electrostatic painting in Melbourne Village is not the same job it would be inland. Brevard County homes deal with salt air blowing off the Indian River and the Atlantic, months of high humidity, daily summer rain and relentless UV. Those conditions shorten the life of the wrong product dramatically — and they punish shortcuts in prep even harder. A coating that fails early in Melbourne Village almost never failed because of the paint; it failed because the surface underneath was not clean, dry, sound and primed before the finish went on.

So we start with assessment, not with a price. We inspect the existing finish for adhesion, chalking and mildew, check for moisture and hidden water damage, identify substrate type, and flag the repairs that have to happen first — stucco cracks, failed caulk joints, soft wood, drywall damage, or slab prep on coating work. You get a written estimate that itemizes prep, products, coat count, crew size and timeline, so nothing shifts once work begins.

The work itself follows a fixed sequence: protect the space and surroundings, clean and de-gloss or wash, complete every repair, prime the areas that need it, then apply two full finish coats of premium coatings selected for Florida coastal exposure. We spray, roll or brush based on what the surface calls for rather than what is fastest, and we hand-cut lines for a crisp edge. Nothing gets signed off until we have walked the job with you and touched up anything you point out.

Practical details matter as much as the finish. Our Melbourne Village crews are licensed, insured and background-checked, arrive when we said we would, cover and mask thoroughly, and clean the site daily instead of at the end. You will have one point of contact for the whole project and a written warranty on workmanship. Free estimates are available across Melbourne Village and the wider Space Coast, and every homeowner is welcome — including LGBTQ+ families.

Our electrostatic painting process in Melbourne Village

Step 1
Survey and ground plan
We walk the items with you, confirm each piece is bare or coated metal that will hold a ground, note what has to stay in service, and schedule around your hours.
Step 2
Contain and mask
Floors, glass, hardware and adjacent finishes are protected and the work zone is contained. Because the charged coating is drawn to the metal, masking is a fraction of what conventional spraying needs.
Step 3
Clean, de-gloss and ground
Metal is degreased, rust and failing coating are removed, glossy factory finishes are abraded, and a ground clamp is attached so the electrostatic charge has a path.
Step 4
Spray, cure and reset
A DTM or industrial enamel is applied in even passes, allowed to cure, and the space is put back the way you use it — usually the same day for doors and railings.

Refinished in place — no removal, no sending items out
Charged coating wraps edges, hinges and tube railings
Minimal overspray, so offices and clinics stay open
Metal doors, frames, railings, lockers, panels and equipment
Evening and weekend scheduling for occupied buildings

Electrostatic Painting neighborhoods in Melbourne Village

Hammock Road
Fern Street
Ash Road
Dayton Boulevard
Village Common
US-192 corridor

Our prep standards for electrostatic painting

Prep is the part of the job you never see once we are gone, and it is the only reason a finish lasts in Brevard County's heat, salt and humidity. This is the sequence we follow on every electrostatic painting job — it is written into your estimate, not left to chance.

Step 1
Confirm the metal will ground
Every item is checked for a clean electrical path — bare or coated steel, aluminum and galvanized all work, but a ground clamp has to reach sound metal. Wood, plastic, fiberglass and drywall in the same scope are noted for conventional spraying instead.
Step 2
Degrease before anything else
Door faces, push plates, railings and equipment housings carry hand oils, silicone sprays and shop grease. They are washed with a degreaser and rinsed, because a charged coating still fails over a contaminated surface.
Step 3
Treat rust and failing coating
Corrosion, scale and lifting paint are wire-wheeled or sanded back to sound material and spot-primed with a rust-inhibitive primer — critical on Brevard County exterior railings and door frames exposed to salt air.
Step 4
Abrade the factory gloss
Baked factory enamels and powder coats are scuff-sanded so the new film has mechanical bite in addition to the electrostatic attraction.
Step 5
Contain, protect and ground
Glass, hardware, floors and adjacent finishes are masked, the work zone is contained, hinges and lock hardware are protected or removed, and the ground lead is attached before the first pass.

Coatings and materials we use for electrostatic painting

We spec products for Florida exposure, not for the lowest material cost. Here is the system, layer by layer, and why each layer is there.

Electrostatic Painting coating system used by Pro Touch Painting in Brevard County, FL
Layer	What we use	Why	Coats
Rust treatment	Rust-inhibitive metal primer (spot)	Stops active corrosion under the finish, which is the usual failure point on coastal metal.	Spot, as needed
Bonding primer	Direct-to-metal bonding primer	Gives slick galvanized, aluminum and powder-coated surfaces something the finish can hold onto.	One where required
Finish — interior metal	Waterborne acrylic-urethane or DTM enamel, satin or semi-gloss	Hard, cleanable film for doors, frames, lockers and partitions in occupied buildings, with low odor and fast return to service.	Two
Finish — exterior / industrial	Industrial DTM urethane or epoxy-modified enamel	Rated for UV and salt exposure on railings, gates, fencing, HVAC housings and equipment.	Two

Rust treatment
Rust-inhibitive metal primer (spot)
Stops active corrosion under the finish, which is the usual failure point on coastal metal.
Spot, as needed
Bonding primer
Direct-to-metal bonding primer
Gives slick galvanized, aluminum and powder-coated surfaces something the finish can hold onto.
One where required
Finish — interior metal
Waterborne acrylic-urethane or DTM enamel, satin or semi-gloss
Hard, cleanable film for doors, frames, lockers and partitions in occupied buildings, with low odor and fast return to service.
Two
Finish — exterior / industrial
Industrial DTM urethane or epoxy-modified enamel
Rated for UV and salt exposure on railings, gates, fencing, HVAC housings and equipment.
Two

What drives the price of electrostatic painting in Brevard County

Electrostatic painting is quoted per item and per access condition — door and frame counts, linear feet of railing, or equipment footprint — after a site walk, because prep condition drives most of the labor.

Item count and size
Twelve hollow metal doors and frames in one corridor is efficient work; twelve doors spread across four buildings is not.
Condition of the existing finish
Sound factory enamel needs a clean and a scuff. Rusted, chalking or peeling metal needs mechanical removal and spot priming first.
Color change and coverage
Going dark-to-light, or matching a specific brand color, may add a coat.
Access and scheduling
Elevated railings, lifts, secured areas, and after-hours or weekend windows in occupied buildings all affect the number.
What else is in the scope
Metal refinished during a larger commercial repaint costs less than a standalone mobilization for a handful of doors.

Electrostatic Painting in Melbourne Village — questions

Do you offer electrostatic painting in Melbourne Village, FL?: Yes. Pro Touch Painting serves Melbourne Village and the surrounding Brevard County area with licensed, insured crews. Call 207-812-1837 for a free written estimate.
What is electrostatic painting?: Electrostatic painting is a spray method that gives the paint particles an electrical charge so they are attracted to grounded metal. The coating wraps around the whole surface — front, back, edges, hinges and railing undersides — and very little of it drifts as overspray. That makes it the standard way to refinish metal on site instead of removing it or replacing it.
What can be electrostatically painted?: Any grounded metal: hollow metal doors and frames, handrails and guardrails, lockers, shelving and racking, storefront and window frames, elevator doors, partitions, filing cabinets, electrical panels, HVAC units, machinery housings and metal fencing. Wood, drywall, plastic and fiberglass cannot hold the charge and are painted conventionally instead.
Can you paint while our building stays open?: Yes — that is the main reason to choose it. Because the charged coating is pulled to the metal rather than into the air, containment and masking are far lighter than conventional spraying, so we work in occupied offices, schools, medical suites, retail spaces and warehouses, section by section, including evenings and weekends.
Is electrostatic painting cheaper than replacing metal doors or railings?: In almost every case, yes. Refinishing keeps the existing hardware, frames and openings, so there is no demolition, no lead time on new metal and no code or fire-rating re-approval on rated doors. Every project gets a free written estimate that itemizes prep, coating system, coat count and schedule before any work starts.
How durable is the finish in Florida's coastal climate?: We specify direct-to-metal industrial enamels and urethanes rated for salt exposure and UV, which matters in Brevard County where salt air off the Indian River and the Atlantic attacks unprotected steel and aluminum. Rust is treated and spot-primed before finish coats so the film is not sitting on top of active corrosion.
Do you offer electrostatic painting outside Melbourne?: Yes. We cover all of Brevard County — Melbourne, Palm Bay, West Melbourne, Viera, Suntree, Rockledge, Cocoa, Merritt Island, Titusville, the beachside communities and the Port — for commercial, industrial and property-management clients.
Is it new for Pro Touch Painting?: Electrostatic painting is our newest offering, added alongside our commercial painting work so property managers and facility teams can keep metal looking new without replacing it. It is booked and scoped exactly like the rest of our work: a site walk first, a written scope second.